About This Equipment
This power supply works for my lower power equipment. I got this one in particular because I needed AC for the Tube MP Studio.
Initially, I tried velcroing it to the bottom of ther board, then to the top. In both cases, it emitted some humming. Not terrible, but noticable. Finally I drilled the holes and mounted it properly under the board, and voila, no hum!
I'm not really a hands-on guy, so mounting was a big task. I'm proud that I got through it with only one extra hole in the board, only one hole in the floor, and only one broken drill bit. Success.
| Purchased From | Sweetwater |
|---|---|
| Purchase Date | 2022-10-09 |
| Brand | CIOKS |
| Model | AC10 10-output 6 Isolated Section Guitar Pedal Power Supply |
The following information was obtained from the Manufacturer's Website
AC10 is a member of CIOKS professional range of dedicated multi-output power supplies for effect pedals. Its two powerful AC sections with 800mA each offer voltages 9, 12 and 16V AC. If you have one or two pedals in your setup, which requires an AC power source, AC10 is the right choice. It powers all vacuum tube pedals from Electro-Harmonix, Kingsley, older Blackstar HT series, the Whammy or JamMan from DigiTech, Tube Rotosphere, Tubeman, Tube Factor or Replex from Hughes & Kettner or EBS Valve Drive just to mention a few. If you only have one AC pedal, you can convert one of the AC sections into a powerful DC section offering 600mA with voltages 9, 12 and 15V DC. The first 4 isolated outlets offering 600mA are perfect for pedals using 9 or 12V DC at lower currents up to 200mA.
Features
- 10 outlets configured in 6 isolated sections
- Toroidal transformer with additional electromagnetic field shielding
- 2 powerful AC sections with 800mA each
- 9, 12 and 16V AC available
- One AC section convertible into a 600mA DC section
- 15V option for Radial Tonebone pedals
- Short circuit protection of all outlets
- Advanced LED monitoring of each section
- 120 or 230V mains voltage operation
- Total of 16 Flex cables in total included
- Split Flex for powering two pedals of one outlet included
- Stack Flex and Series adapter Flex for powering 18 or 24V pedals included
- Flex cable for Electro-Harmonix vacuum tube pedals included
- Compatible with Pedaltrain and Temple Audio pedalboards
- Mounting bracket and all pedalboard mounting hardware included
Specifications
- Outlet 1-2: 9V DC / 100mA each
- Outlet 3-4: 9 or 12V DC / 200mA each
- Outlet 5-6: 9 and 12 or 15V DC / 600mA*
- Outlet 7-8: 9 or 12V AC / 800mA*
- Outlet 9-10: 9, 12 or 16V AC / 800mA
- Size: 158x98x35mm (excl. rubber feet)
- Weight: 1.1kg
*only one of these two sections can be used
What's in the Box
- CIOKS AC10 power supply
- Mains power cord
- 17 Flex cables:
- Type 1 – black with 5,5/2,1mm centre negative DC plug x8
- Type 2 – red with 5,5/2,1mm centre positive DC plug x1
- Type 4 – green with 5,5/2,5mm centre positive DC plug x2
- Type 5 – black with 3,5mm tip positive Jack plug x1
- Type 6 – black with 9V battery clip x1
- Type 7 – blue with 2 pin DIN plug x1
- Split Flex type 1 – powers two pedals of a single outlet x1
- Stack Flex type 1 – white/black, adds voltages of two outlets x1
- Pedalboard mounting hardware: mounting bracket, screws, washers, stand-off and a hex key
- Manual
- Product sheet (drill guide)
- Flex guide
Documentation
Gallery
 |
 |
|---|---|
 |
 |
 |
 |
 |
 |